MightySeal Waterbar - An elastic PVC waterstop made from high-quality, heat-resistant, elastic polyvinyl chloride. The product is designed to prevent water seepage through construction joints, expansion joints, and settlement joints in concrete structures. MightySeal Waterbar meets the technical requirements of TCVN 9407:2014 and BS 2571.

MightySeal CP là hệ chống thấm 2 thành phần gốc xi măng polyme, được chế tạo từ polyme chất lượng cao, xi măng chọn lọc và các loại phụ gia cao cấp khác. 

MightySeal CP sau khi trộn sẽ trở thành hỗn hợp dẻo, mịn có thể dễ dàng thi công bằng cọ, rulo hoặc máy phun phù hợp. 

MightySeal CP được thi công trên bề mặt ẩm tới bão hòa (nhưng không để đọng nước). Màng phủ sau khi đóng rắn có cấu trúc đồng nhất, có tính năng dẻo dai, bền và bám dính tốt với hầu hết các bề mặt xi măng bê tông. 

MightySeal AC is a water-based, acrylic, elastic waterproofing coating for waterproofing, heat insulation, and building protection. The product is easy to apply on both horizontal and vertical surfaces, forming a seamless, hydrophobic, elastic membrane with high UV resistance and mechanical stress resistance. Apply MightySeal AC with a brush, roller, or spray gun in a minimum of two coats. The number of coats depends on actual requirements.

MightySeal PU W is an elastic, water-based modified aliphatic polyurethane coating for waterproofing and protecting structures. The product is easy to apply on both horizontal and vertical surfaces, forming a seamless, hydrophobic, elastic membrane with high resistance to ultraviolet (UV) rays and mechanical stress. Apply MightySeal PU W with a brush, roller, or spray gun in a minimum of two coats. The number of coats depends on actual requirements.

MightySeal US Primer is a one-component, low-viscosity polyurethane primer suitable for a wide variety of substrates. The product cures upon contact with moisture.

HYPERSILICA™ 92U is a highly reactive, ultra-fine, non-compressed silica fume (also known as microsilica) mineral additive. Its main component is amorphous spherical SiO2 mineral obtained during the arc production of silica and silica alloys from quartz.

The average particle size of HYPERSILICA™ 92U is approximately 5 microns, which is 100 times smaller than cement particles.

HYPERSILICA™ 92U conforms to the following standards: US ASTM C-1240; Canada CAN/CSA-A23.5, Europe EN 13263, Japan JIS A6207, Korea KS F2567, China GB/T18736, and Vietnam TCVN 8827.

VINMASTIC is produced from high quality bitumen, modified with special agents. It is dark, hot - applied. VINMASTIC  meets requirements of ASTM D1190, ASTM D6690 và TCVN 9974.

HYPERFLOOR® QH is a dry shake, ready-mix powder mixture, use for increasing hardness of concrete floor surface. The product is manufactured from high quality selected natural quartz sand, cement, additives

HYPERBITS® C60 is a cementitious, ready to use polymer modified self-leveling non-shrink grouting motar with high intial and final strengths. Pre-mixed with selectively graded materials result in a dense homogeneous mix.

HYPERLATEX® ECO is a modified polystyrene butadiene emulsion system, milky white in color. The product is mixed with cement to act as a bonding agent between old and new concrete layers, or mixed with cement/sand mortar to enhance the waterproofing properties of the mortar.

HYPERLATEX® is a white milk modified poly styrene butadiene emulsion. The product is mixed with cement for improving adhesion between old and new concrete and or mixed with cement/sand motar for improving waterproofing resistance of motar, …

HYPERLATEX® is a modified polystyrene butadiene emulsion system, milky white in color. The product is mixed with cement to act as a bonding agent between old and new concrete layers, or mixed with cement/sand mortar to enhance the waterproofing properties of the mortar.

IDROPOL is a polymer-modified waterproofing membrane obtained from the modification of distilled bitumen with poly-olefin based copolymers The modified compound makes Idropol an easy to apply membrane that requires low consumption of gas and has excellent adhesion properties that ensure, when the membrane is properly installed, very good bonding and tightness ofall joints and overlaps. The carrier is a composite polyester stabilised with longitudinal glass yarns that provide very good dimensional stability and prevent problems of shrinkage caused by weathering in time.

Available surface finishes.

Upper surface: talc or sand (IDROPOL) or self protected with natural grey or coloured slate flakes (IDROPOL Mineral).

Available upon request: upper finish with TEX (non-woven black poly-propylene) or plastic PP/Pe films.

Lower surface: polypropylene fast burning film.

HYPERBITS® TCS is a non-woven compound reinforced, SBS modified bitumious waterproofing sheet membrane. Product is manufactured on advanced and modern technological line. HYPERBITS® TCS has stable dimensions, high tensile strength, high elongation at break and excellent mechanical properties.

HYPERBITS® TCA is a non-woven compound reinforced, APP modified bitumious waterproofing sheet membrane. Product is manufactured on advanced and modern technological line. HYPERBITS® TCA has stable dimensions, high tensile strength, high elongation at break and excellent mechanical properties.

AUTOTAK is a self-adhering waterproofing membrane made of distilled bitumen modified with SBS (styrene-butadiene-styrene) polymers, with an adhesive coating on the lower face and a self- protecting upper PE/Sand surface. The carrier is a composite polyester stabilised with longitudinal glass yarns that combines superior dimensional stability with good tensile strength, elongation values and excellent mechanical properties in general.

Available surface finishes
- Upper surface: Sand (Autotak 2.0 mm) or plastic PE film (Autotak 1.5 mm)
- Lower surface: silicone release film.

BITUSTIK is a self-adhering waterproofing membrane made of distilled bitumen modified with SBS (styrene-butadiene-styrene) polymers, with an adhesive coating on the lower face and a self- protecting upper PE/Sand surface. The carrier is a composite polyester stabilised with longitudinal glass yarns that combines superior dimensional stability with good tensile strength, elongation values and excellent mechanical properties in general.

Available surface finishes
- Upper surface: Sand (Autotak 2.0 mm) or plastic PE film (Autotak 1.5 mm)
- Lower surface: silicone release film.

HYPERBITS® APS is a non-woven polyeste reinforced, SBS modified bitumious waterproofing sheet membrane. Product is manufactured on advanced and modern technological line. HYPERBITS® APS has stable dimensions, high tensile strength, high elongation at break and excellent mechanical properties.

HYPERCOAT® EPS-2K-KOI is a high-quality, two-component epoxy resin-based waterproofing coating specifically designed for waterproofing fish tanks and koi ponds. The product is black, easy to apply on both horizontal and vertical surfaces, and forms a seamless membrane. HYPERCOAT® EPS-2K-KOI can be applied using a roller, brush, or spray gun.

VINCOAT™ is a water based polymer modified bitumen elastomeric coating for waterproofing and protection.The product is easily applied on both vertical and horizontal substrates and forms a seamless, elastic membrane.

Apply with brush, roller or airless spraying in two or more coats. The quantity applied is depending on the final use requirements.